Inglenook 5 Piece Black And Chrome Fireset With Oval Handles

Product Information

Uses - Provides for safe operation of all Explosive Services including Perforating, Pipe Recovery, Setting NOTES: All safety features were tested and certified at Sandia National Laboratories by Orion International Technologies Inc. All tests were done at ambient temperature, and all tests (apart from the lightning strikes) were repeated at 93°C - 121°C.​ Standard-equipped with an air vent valve und pressure gauge installed directly on the main pump housing Typically: shopping centres, supermarkets, industrial processes and buildings with a highly combustible load. Diesel pumpset (including pump-end, diesel engine, 6 hour single-walled fuel tank, 24v ni-cad batteries and controller within a single skid)

switchgear fixed to a robust support structure. Model E for the electric motor and D for the diesel motor, both with a WiZiTouch controller by Tornatech. Typically: large schools and offices, hospitals, hotels, restaurants, libraries, dairies, cement works, sheet metal producers and abattoirs. Radios stay on; communication links are unbroken; helicopter flights continue; construction work is uninterrupted; production is unaffected; the use of sensitive primary explosives is avoided. All of these advantages are available with the PX-1 fireset from Ecosse. Extensive range of end-suction pumps available to suit requirements for fully hydraulically calculated systems giving a wider range to suit individual selection requirements. Sensors and display: The pressure transducer is located on the switchgear and activates the pump start via the controller. The pressure gauge on the suction and pressure side (ø63mm) is located on the pump’s split housing.All products are LPCB listed and approved to BSEN12845, ensuring that they follow the correct criteria offering the peace of mind that they will work effectively. Automatic supply change-over panels (used on twin electric pump installations to alternate incoming supplies to each pump) allow it to fit in virtually every gun system in use today, including pressure housings with an OD of 1-3/8”. Diesel pumpset (including pump-end, FM/UL approved diesel engine, 8 hour double-walled fuel tank*, 12v lead acid batteries, LCD colour display controller, suction and discharge pressure gauges and air release valve all on a single skid)

Typical high hazard applications are storage and distribution facilities, areas where chemicals exist and high rise buildings over 45m. Benefits Please note an 8 hour double-walled fuel tank is as per the requirements in Factory Mutual Datasheets. Within NFPA20 a single-walled fuel tank sized to 5.07 litres per kW is acceptable, which is also available upon request. What standards is this equipment approved / compliant to?

FM/UL fire set

The purpose of the FS-43 Firing Module is to provide a significant amount of flexibility to this EBW detonator firing system. Since the firing pulse to function the EBW detonator must be applied at the proper rate of rise, or frequency, the firing module must be placed relatively close to the detonator. By being able to separate the Firing Module from the control unit, the operator can perform the detonation at extended distances as required by the size and characteristics of the main explosive charge.

The purpose of the FS-43 Control Unit is to provide low voltage electrical energy to the Firing Module and to ensure a safe and reliable operation sequence for the firing of EBW detonators. Pumps can be produced in higher grade materials for specific pumped liquids ensuring reduction of corrosion damage and increasing longevity of the product. BSEN12845 – Fixed firefighting systems, automatic firefighting systems, design, installation and maintenanceLPS1131 1.1 – Requirements and testing Methods for pumps for automatic sprinkler installation pump sets The SP-1005 is typically tripod mounted. It is self-contained, and battery operated. Size is approximately5 x 4.5 x 4.5 inches, overall. It weighs just under 2 pounds. Its output is a nominal 7.5-volt pulse from a 50-ohm source. Unlike conventional hot-wire and hot-resistor detonators normally used in oilfield perforating operations, EBW and EFI detonators do not contain sensitive primary explosives such as lead azide. from 260kHz at 50V/m, electrostatic discharges, and severe direct lightning strikes to the wireline stray DC voltages from -600VDC to +150VDC, AC voltages at 600V rms from 40Hz through 20kHz, RF testing

Within the UK, each building is defined by criteria of the installation and a relevant insurance body is appointed. If assigned to LPCB, then a hazard category would also be assigned. There are three of these - light hazard, ordinary hazard and high hazard and all are ranked depending on the combustibility rate of the items within the building (for instance, a high combustibility would be considered a ‘High Hazard’). Applications Within the UK, each building is given a designation that is defined by a number of criteria and given a hazard category. Standard categories are: Connect the EBW detonator to the OUTPUT of the PM-100 using a maximum of 100 ft. of RISI twin lead cable, P/N 167-8559, or a maximum of 300 ft. of RISI coaxial cable, P/N 167-2669. A wide selection of options and accessories are available including pump housing to facilitate the selection of the correct equipment.

High Hazard Fire Set

standards that exceed any practical level of threat that might exist in the oilfield environment, including Connect the OUTPUT of the blaster to the INPUT of the PM-100 using RISI twin lead cable, P/N 167-8559. within 3ft of the PX-1 itself. Particularly on offshore platforms, these safety features can result All components within the pumps are independently approved and tested ensuring the product meets the expected high quality. Tank: Fuel tank made from epoxy painted steel with a strong support structure. Fully equipped with a fuel gauge, drain plugs and air vent valves.